massburma3

How to Replace a Kia Sportage Replacement Key The key in many Kia models comes with the keyless entry feature built into. This key usually resembles a remote control and is able to be replaced by a new one purchased from a Kia dealer or a locksmith. Key fobs may stop working due to a number of reasons, including an inactive battery, worn out buttons signals, signal interference or water damage. Here are some tips to help you get your Kia sportage replacement key to work once more. How to replace a smartkey or remote key? If your Kia comes with an intelligent key, remote key push to start key or a regular non-transponder steel key The battery inside these keys will eventually need replacing. This is particularly true if the car displays a message indicating that the smart or remote key has low battery power. This is a relatively easy process. To replace the battery of the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, pry the cover off. Inside the key fob will be tiny screws that hold the battery in place. Utilizing a small screwdriver loosen the screw and remove the old battery. Then insert the new one and close the slit on the key fob. Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock as expected, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you have to run errands around Brandon. Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a computer that is only available to the locksmith for cars or dealer. Other keys (non transponder metal keys) don't require programming. If your keys need to be programmed again, you will need to be aware of the key code number printed on the tag of the key code and keep it in a safe place. How do you replace a dead battery? If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is insufficient. A battery that is not functioning properly could cause other issues such as the check engine light coming on or delayed engine cranking. It is relatively easy to replace key fob batteries with only a few simple tools. Before beginning the process ensure that your vehicle is off and that all doors are closed. Locate the small plastic piece on the bottom of your key fob and move it until a metal key slips out. The key can be put into the door's driver handle to unlock your car. To replace the key fob battery, remove the cover on the rear and use a plier bar tool to remove the latch that holds the black negative battery cable. Remove the old battery, and then align the new one so that the “+” positive side is facing you and the “–” negative side is facing towards the fob's metallic electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts. After the new battery has been installed then turn the key fob off and then on in the ignition until the door locks cycle. You can then test the Kia's Key fob again to make sure it is working correctly. How do you replace a smart keys You could have a standard keyfob, or a Smart Key based upon the model of Kia Sportage. The smart key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs contain a battery inside them that eventually will need to be replaced. It is a simple process that takes just two minutes. Before you start it is important to ensure that you're on a level surface with adequate lighting and that your Kia is not on. Also, keep in mind that there are tiny parts inside the fob that can be removed if not careful. The small release button is located on the lower backside. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button. Once you have the key fob opened it is easy to remove the old battery, and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. Once you're done you should be able to lock or unlock your vehicle using your key fob – even if your engine isn't running! How to replace the mechanical key? The Kia keyfob is a great convenience, allowing us to lock or unlock our car simply by pressing the button. Like all devices like a key fob, the Kia can occasionally have problems. There are steps to take to solve these issues and keep our key fobs in good condition for the long run. A dead or drained battery is among the most frequently encountered issues. This could cause the fob to stop working altogether or to work intermittently. If this is what you are experiencing then replace the battery with an entirely new battery. If this does not solve the issue, try using the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be kia duplicate key not to damage any internal components or scratch the plastic. Once the battery is removed, replace it with a new one. Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and ensure that it's working properly. Contact a dealer or locksmith to solve the issue in the event that the fob is not working. To avoid a lockout in the future ensure that you have an emergency key that can work in all of the trunk and door cylinders.